Optionals

Interior exhaust valve to discharge the air present in the piece at the end of the test. The time of this phase can be set in the menu TST of the instrument.

Pneumatic circuit with component mounting high flow to speed up the filling phase for large test volumes. The filling speed is 4 times higher for an instrument with standard pneumatic. Includes precision pressure regulator.

Pneumatics and valves with very small volumes and high speeds drive: it allows great accuracy and speed on small volume pieces under test.

Includes internal pneumatic filling branch hydrogen and sniffer manual for position detection loss.

Staubli© fittings for the connection to the front panel of calibrated leaks Leak_ID or of third parties, by Staubli® hermetic fitting.

Application of a mechanical regulator at very high precision: it can regulate pressure test with better accuracy and stability. Recommended for low pressures.

Internal card to interface the instrument to a Profinet network compatible with the most common industrial PLCs.

Dynamic correction of the measurement error test after test. It allows to eliminate slow drift errors due to environmental conditions or errors of the test bench.

Internal Ethernet card to interface the equipment to an EtherCAT fieldbus controller

Measurement of the piece temperature and the ambient temperature allowing to apply a compensation

Volume and the leakage of an hermetic piece in a bell

EtherNet/IP™ is a common industrial communication protocol (CIP) that reduces integration costs. EtherNet/IP provides the ability to control, configure, send and receive messages between ForTest T-Series equipment and Rockwell/Allen-Bradley PLCs.

Application of an Electronic pressure regulator at very high precision for the automatic pressure setting; recommended where it is necessary a very high test precision or where it is necessary to change often test pressures. This option provides the installation of an internal expansion board in addition to the piezoelectric regulator and a dedicated pneumatic circuit.

It allows to make a phase of auto calibration of Zero drift of pressure

Bluetooth Low Energy communication interface

Application of a pneumatic branch and of negative gage pressure measure, besides the conventional positive measure of scale. It is possible to set in the menu TST the desired pressure (positive or negative) and automatically the instrument will proceed to the filling with positive or negative pressure, based on the set value.

By the application of two mechanical manual regulators or by an electronic pressure regulator, it allows to perform the Filling Step with two or more pressures differents among them in order to reduce elastic and thermal phenomenons of the piece under test, reducing the time of Adjustement phase.

It allows to display the direct pressure, besides in TEST steps also during Waiting and Stand By Step

Particularly used on foundry pieces, it allows to add to the normal Good Waste threshold also a non-recoverable waste threshold (for Foundries: threshold of maximum chemical potting).

Enables the barometric pressure measurement. It compensates for the measures to suit the change in ambient pressure.

Analog Output 0-10 V on AUX2 connector that repeats the loss detected in auto scale with the programmed loss.

Expansion with 8 outputs (24 Vdc source type, max 2 A, opto isolated, completely safe) and 4 24 Vdc input Opto type.

It accepts Start cycle by two separate Start signals (instead of only one) adhering to the regulations for bi-manual command EN 574. ATTENTION: Unless different annotations contained in each instrument handbooks, this sequence means to make safer the instrument utilization for single use and it cannot in any case be intended as a safe element for other parts handling (ex: presses, control cycles, etc...) connected to them.

Ethernet connector for PC network connexion. It enables autonomous functions of connection TCP-IP and functions of direct connection to internet network with configurable IP.

USB port of Host type for the connection of a key storage for test results and for the copy of test parameters from an instrument to another one.

WI-FI connection 802.11 g for wireless connection of the instrument to PC.

4 channels Radio remote for instrument remote management. Frequency 433,92 MHz; 20m-100 run in open space. T

By the application of superior components and transducers , a metrologic resolution of the measure of 1.000.000 points is guaranteed.

Application of a volumetric capacity meter designed to determine automatically the cavity volume of the piece under Test. Besides it allows to make volume Tests with waste generation.

Double branches of automatic pre-regulated pressures. By the application of two manual mechanical regulators, it is possible to change two pressures different among them.